Made for concreters by concreters

Australian Made Logo

Prime One Coat Sealer

Our Prime One Coat Sealer is UV resistant and will protect your concrete from mould, staining, algae, moss and repels dirt, grime and oils.
Prime Exposure Acrylic One Coat Sealer is made using the finest acrylic polymers and is blended in Australia for Australian conditions.

Prime Exposure One Coat Sealer has been specifically designed to save time and money whilst delivering the same results as a two coat process.
Our Prime Exposure One Coat Sealer will enhance the look of your decorative concrete and keep it looking like new for years.

Coverage: Approximately 70-80m2 per 20 Litre Drum

Prime Exposure produces a number of sealers, to see our full sealer range click here!

Application Guide

Surface Preparation

Check the concrete is sufficiently cured, pressure clean the surface (above 2000 psi is preferred) and ensure the surface is free of any grease, oil or any foreign contaminates.

Remove any loosely bound cement and efflorescence by acid etching with hydrochloric acid diluted at approximately 9 parts water to one part acid. Do not allow the acid to dry on the surface during this process, thoroughly rinse the surface with fresh water using a garden hose. You must allow the concrete to thoroughly dry prior to sealing!

Any moisture will affect the sealer, making it look white and cloudy. Moisture will stop surface adhesion and cause delamination.

Application

The surface should look totally even in colour prior to applying Prime Exposure One Coat Sealer, if the surface is not, the cleaning process has to be completed again until the surface is uniform in colour. Any contaminates or efflorescence will be locked under the sealer coating and will remain for the life of the coating.

  • Prime Exposure One Coat Sealer cannot be used undiluted on flat trowelled, stippled or unsealed slate impression concrete. Our One Coat Sealer has been designed to be applied neat on unsealed Exposed Aggregate concrete.
  • We recommend applying Prime Exposure One Coat Sealer with a good quality roller as this will ensure there is an even coating with no pooling and reduce the amount of lost time in replenishing the roller with sealer.
  • After stirring well, apply one even coat with no thinning down for Exposed Aggregate concrete as the surface is porous which allows the sealer to penetrate the concrete surface for suitable adhesion.
  • Do not drive on the newly sealed surface for 3-4 days to allow the resin to harden.

Prime Exposure One Coat Sealer can be used the same as Standard Sealer if diluted with Xylene by 20%.

Resealing

For resealing we recommend you follow the above surface preparation process and once the surface is totally dry, apply a coat of Prime Exposure Xylene to reactivate any existing sealer to assist penetration. After the surface has dried follow the application steps.

Important Notice

PLEASE READ THESE IMPORTANT DIRECTIONS PRIOR TO USE

SAFETY DIRECTIONS: Please ensure adequate ventilation, avoid breathing vapours by using Australian Standard class p1,p2 particulate respirator ensuring it is fitted correctly.

Do not use Prime Exposure Sealer whilst smoking or near naked light or flame. Remove all non-canned foods from area if adequate ventilation is not possible during application or drying.

AVOID CONTACT WITH SKIN OR EYES: Should any irritation occur please seek medical advice.

CURING: Freshly placed concrete should be cured for approximately 7 days subject to ambient temperatures prior to applying any sealer.

SPILLS AND DISPOSALS: It is important to keep all sealers & xylene out of sewer and storm water drains. If spills occur, remove or isolate all ignition sources. Contain and absorb spill in dry, inert material such as sand. Collect in sealable containers and dispose of as trade waste in accordance with local authority guidelines.

Do NOT pour any leftover product down the drain.

CLEAN UP: Wash all equipment thoroughly in Prime Exposure Xylene and allow to dry.

CAUTION: Sealing concrete, slate, paving or slate impression concrete etc. can cause surface to become slippery particularly when wet.

SAFETY: We recommend the use of Prime Exposure Anti Slip (glass beads) be applied with the SEALER to “REDUCE” the risk of slipping when wet.

No responsibility can be accepted or any express or implied warranty given where performance of the product is affected by surface preparation, method of application or any other circumstances beyond the company’s control.

STIR WELL BEFORE USE, CONTAINS LIQUID HYDROCARBONS

NOT TO BE TAKEN, KEEP OUT OF REACH OF CHILDREN